Applied-motion ST10-C-CE Bedienungsanleitung Seite 10
- Seite / 101
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
10
920-0025 Rev K
3/5/2015
CANopen User Manual
Wiring the CANopen Connector for CANopen Drives
Please refer to Applied Motion Products CANopen Drive Hardware Manual for the Com-
munication connection. As an example, we use the connections for the ST5-C drive.
Applied Motion Products ST5-C drive uses a four-pin spring connector, shown in Figure 2
below, and conforms to CiA303 specication. The connector should be wired in a daisy-chain
conguration, as shown in Figure 3 below, with a 120 ohm resistor used to terminate each end.
Other wiring topologies, such as star networks, are not recommended due to wave reection
problems. Please reference specic hardware manuals for your drive’s wiring conguration.
Figure 2: The CANopen Connector
Figure 3 shows a CANopen network with two Applied Motion Products ST5-C drive con-
nectors wired to a Kvaser Leaf USB to CANopen Adapter.
Figure 3: Wiring Schematic
CANopen BitRate & NodeID
Applied Motion Products CANopen drives have three settings, one for Bit Rate and two for
Node-ID.
The Bit Rate is congured using an 8-position switch. See Table 1 for the Bit Rate settings.
Please reference the drive’s hardware manual for the location of the Bit Rate switch.
GND
CAN_L
SHLD
CAN_H
1
.1” Spacing Spring Plug
DSUB9 Female
R termination:
Network must be terminated at each
end with a 120 ohm resistor.
n:
Cable may be made with up to 127 drive
connectors. Termination is only required
at each end.
.1” Spacing Spring Plug
n*
R termination*
120 ohm nominal
R termination*
120 ohm nominal
1
CAN_L
CAN_L
CAN_GND
CAN_GND
CAN_BUS
CAN_SHLD
CAN_SHLD
CAN_H
CAN_H
2
3
4
2
3
4
5
6
7
8
9
1
CAN_L
CAN_GND
CAN_SHLD
CAN_H
2
3
4
- Applied Motion Products 1
- CANopen Manual 1
- Introduction 2
- User Advisory: 2
- Contents 3
- List of Tables 6
- Reference Documents 8
- Commonly Used Acronyms 8
- Drive Setup 9
- CANopen BitRate & NodeID 10
- Drive Conguration 11
- Figure 4: 12
- Object Dictionary 13
- Electronic Data Sheet 14
- INTEGER16 RW Yes 16
- Table 5: CiA 402 Objects 17
- 920-0025 Rev K 18
- 3/5/2015 18
- CANopen User Manual 18
- General Purpose Registers 19
- Index (hex) Object 20
- Communication Prole 21
- COS Default value 25
- Subindex Name Default value 25
- Object Type Sub Number 30
- Manufacturer Specic Objects 38
- Device Prole 45
- 0x6041 StatusWord 46
- Mode of Operation Action 49
- Position polarity 52
- Bit number Description 56
- Appendix C - Response Codes 60
- General Mode Description 61
- Enable Prole Position Mode 61
- Set Running Parameters 61
- Starting/Stopping Motion 61
- Figure 12: Single Set-Point 62
- Enable Prole Velocity Mode 66
- Enable Drive Operation 66
- Appendix F - Homing Methods 68
- Homing Method 2 69
- Homing Method 3 69
- Homing Method 4 70
- Homing Method 5 70
- Homing Method 6 71
- Homing Method 7 71
- Homing Method 8 72
- Homing Method 9 72
- Homing Method 10 73
- Homing Method 11 73
- Homing Method 12 74
- Homing Method 13 74
- Homing Method 14 75
- Homing Methods 15 and 16 75
- Homing Method 17 76
- Homing Method 18 76
- Homing Methods 19 and 20 77
- Homing Methods 21 and 22 78
- Homing Methods 23 and 24 79
- Homing Methods 25 and 26 80
- Homing Methods 27 and 28 81
- Homing Methods 29 and 30 82
- Homing Methods 31 and 32 83
- Homing Method 33 83
- Homing Method 34 84
- Homing Method 35 84
- Enable Prole Torque Mode 85
- Starting/Stopping Torque 86
- Current Verication - Example 86
- Appendix H - Q Program Mode 88
- More Information 89
- NMT Mode NMT Control 90
- NMT Status Code 90
- (Heartbeat) 90
- PDO Access 91
- TPDO Transmission Types 92
- PDO Mapping Procedure 93
- Default PDO Mapping - Stepper 94
- Default PDO Mapping - Servo 94
- PDO COB-ID 95
- Control Word of Homing Mode 97
- Status Word of Homing Mode 97
- Control Word of Q Mode 98
- Status Word of Q Mode 98
- Appendix L – Example Programs 99
- Prole Velocity Mode 100
- Homing Mode 100
- Normal Q Mode 101
- Sync Q Mode 101
- PDO Mapping 101
- Applied Motion Products, Inc 101
Verwandte Produkte und Handbücher für Hardware Applied-motion ST10-C-CE
Hardware Applied-motion STR2 Bedienungsanleitung
(38 Seiten)
(38 Seiten)
Hardware Applied-motion STR4 Bedienungsanleitung
(46 Seiten)
(46 Seiten)
Hardware Applied-motion RS-232 Bedienungsanleitung
(320 Seiten)
(320 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern